[分享]开启ZyXel合勤ADSL MODEM的路由

合勤ADSL P642R 路由方式的设置

先声明:本人不对本文负责,设置带来的一切后果自理

1、 先把你的电脑设置:
进入控制面板,对“网络”进行设置,TCP/IP 协议中的IP 192.168.1.2 子网掩码为:255.255.255.0 DNS设成你当地的值
中山是202.96.128.143
202.96.128.68
2、在开始―运行中输入:telnet 192.168.1.1 点确定。进入P642R的设置主页面。
password:**** (一般默认是1234)

即可进入ZyNOS系统,会看到如下图所示的主菜单
Copyright (c) 1994 - 2000 ZyXEL Communications Corp.

                          Prestige 642R-11 Main Menu  

 Getting Started                      Advanced Management  
   1. General Setup                     21. Filter Set Configuration  
   3. Ethernet Setup                     22. SNMP Configuration  
   4. Internet Access Setup               23. System Password  
                                           24. System Maintenance  
                                           25. IP Routing Policy Setup  
 Advanced Applications  
   11. Remote Node Setup  
   12. Static Routing Setup  
   15. SUA Server Setup                 99. Exit  

设置Router 工作模式:

进入菜单1

Menu 1 - General Setup

                System Name= changeMe  
                Location=aaa  
                Contact Person's Name=bbb  

                Route IP= Yes  
                Route IPX= No  
                Bridge= No  

※注意必须打开Route IP

进入菜单3.2
Menu 3.2 - TCP/IP and DHCP Ethernet Setup

                DHCP Setup  
                  DHCP= Server  
                  Client IP Pool Starting Address= 192.168.1.33  
                  Size of Client IP Pool= 32  
                  Primary DNS Server= 0.0.0.0  
                  Secondary DNS Server= 0.0.0.0  
                  Remote DHCP Server= N/A  
                TCP/IP Setup:  
                  IP Address= 192.168.1.1  
                  IP Subnet Mask= 255.255.255.0  
                  RIP Direction= Both  
                    Version= RIP-1  
                  Multicast= None  
                  IP Policies=  
                  Edit IP Alias= No  

进入菜单4

                     Menu 4 - Internet Access Setup  

                ISP's Name= ChangeMe  
                Encapsulation= PPPoE  
                Multiplexing= LLC-based  
                VPI #= 8  
                VCI #= 35  
                Service Name=    
                My Login= sjz6852xxx@adsl2(你的用户名)  
              My Password=******(你的密码)  
              Single User Account= Yes  
                IP Address Assignment= Dynamic  
                IP Address=N/A  
                ENET ENCAP Gateway= N/A  

进入菜单11.1

Menu 11.1 - Remote Node Profile

 Rem Node Name= ChangeMe             Route= IP  
 Active= Yes                              Bridge= No   

 Encapsulation=PPPoE                    Edit PPP Options=No  
 Multiplexing= LLC-based                  Rem IP Addr=0.0.0.0  
 Incoming:                               Edit IP/IPX/Bridge= No  
   Rem Login=   
   Rem Password=********(不要动这里)  
 Outgoing:                            Session Options:  
   My Login=sjz6852xxx@adsl2          Edit Filter Sets= No  
   My Password=*********                  PPPoE Idle Timeout(sec)=0  
   Authen= CHAP/PAP                      PPPoE Service Name=   

Step 4. 检查设备工作状态
在完成第三步以后,理论上设备应该能正常使用了。此时,可以进入菜单第24项 ― System Maintenance
Menu 24 - System Maintenance

                     1.  System Status  
                     2.  System Information and Console Port Speed  
                     4.  Diagnostic  
                     5.  Backup Configuration  
                     6.  Restore Configuration  
                     7.  Upload Firmware  
                     8.  Command Interpreter Mode  

然后选择第1项 ― System Status,菜单如下图所示。

Menu 24.1 - System Maintenance - Status

Node-Lnk Status TxPkts RxPkts Errors Tx B/s Rx B/s Up Time
1-PPPoE Up 1042 988 0 1052 1052 0:18:21
2 N/A 0 0 0 0 0 0:00:00
3 N/A 0 0 0 0 0 0:00:00
4 N/A 0 0 0 0 0 0:00:00
5 N/A 0 0 0 0 0 0:00:00
6 N/A 0 0 0 0 0 0:00:00
7 N/A 0 0 0 0 0 0:00:00
8 N/A 0 0 0 0 0 0:00:00

Ethernet:                                    WAN:  
  Status: Full Duplex      Tx Pkts: 981        Line Status: Up  
  Collisions: 0             Rx Pkts: 1186       Upstream Speed:   832 kbps  
  CPU Load =    4.49%                             Downstream Speed:  7616 kbps  

在右下角的圆圈中 Line Status:Up 代表ADSL的物理层已经连通,它下面的两项分别是ADSL所使用的上行和下行速率。
在左上角的圆圈中PPPoE代表设备所使用的封装协议为PPPoE ,Up代表协议的工作状